Here is how to update your H502E and H502S drone. This update is only for the drone, I have used, and tested it on a H502E and I can confirm it works. Important is that you have the drone connected to USB, and that it is powered on! Don’t
On this page you can download the H502E-H502S Firmware This is the latest version available 2.1.35. NOTE: INSTALLING 2.1.35 ON A NON COMPATIBLE BOARD WILL BRICK IT! I had enough people trying to update a non compatible board blaming me for spreading faulty firmware, and destroying the hobby of someone. I
As you might have heard the Hubsan H502E/S has it’s problems. Some can fly hours and hours without problems, others crash after 2 flights. I am one of the last, and after changing motors several times, all under warranty, I have had a replacement board from Hubsan. If you want
Not too long ago I have written about my battery mod. I have flown the mod 2 or 3 times, and the only successful one was the first ever flight. Back then I was happy with the results, not knowing what I know now. At an event in December I
Santa gave me a Revell NanoHex, and here is my little review. The contents of the package are: The Hexacopter, a remote, charging cable, instruction manual, and a spare set of propellers. This review is not long, there is not that much to tell, other than that this is a
Today I have received my new gimbal dampers. After replacing them I took them for a test flight. I am very happy with them, and I have lost my last little vibration that I always had in my video’s. The dampers were only €2,13 at AliExpress, and you can get them
UpAir did the same with the LEDs as DJI did, red in front, green in the back. I have swapped them around… Red is now rear, green is the front. It just makes more sense. Sorry for my horrible Phone camera..
As you might have read in my previous post I have had a hard landing with the UpAir. No major damage other than a damper that got lost in the grass. But, the UpAir had a minor deviation to the right and I wanted to know why. So i exposed the
After another motor failure I have repaired the little Hubsan again. Even though this seems to be a big issue on these drones, I can’t stop loving it. It is a great flyer! It’s a pain to open her up every now and then, but when she’s up and running
Even though the UpAir One is a great drone out of the box, there are some ways to get even more fun out of it, and make it even that little bit better. We are able to increase flight times, calibrate compass, change functions from switches, calibrate gimbal and a
Even though all the stuff needed for the mod arrived over a week ago, I still haven’t had time, or the weather did not permit me to fly the mod and actually test it. But today the weather was good, I had some time, and batteries were charged and ready to
For the fourth time the Hubsan needs new motors. I still can’t understand why this happens, but I guess it’s all part of the hobby, and I have accepted it. Bad thing is that is the last set I have as spares, so I need to get ordering new ones soon
The weather is so bad outside, but I had to have my flying fix. Grabbed the little LiDi drone, put in a lipo and there she went… I still like this drone a lot! great fun, even inside You could buy one here if you want one: http://www.gearbest.com/rc-quadcopters/pp_427833.html#lkid=10209927
I have had my fair share of toy-grade drones, and I must say that I am impressed by this one. It doesn’t have all the gimmicks like a compass, barometer, gps, altitude hold and so on yet it is easy to handle outside. This review was made with windforce 2
Today they have finally arrived, my new carbon fiber propellers! The weather doesn’t allow for it to get tested, but will soon post what they are like.
Many have heard and read about the FPV issues with the UpAir One drone. Some people take apart their expensive drone to do all kinds of mods to improve the feed, and the stability of it. they buy more powerful VTX modules and stick on antennas… But there is a